Wednesday, August 17, 2016

Rose^Stirs!!!



The Whoa of Activity on the Tables,
such act.tiers that the rust is made in the throws to just happens??,
not in the say rather the happening,
as that is the Curtain of how it is in an inch to a mile,
it remains to be that shed of tools to touch the lip of raised??.

Not in the County of Fashion,
address and years on the clock,
gossip and silverware to the what did perk grape,
not more than the depth of shallow deep crate.

It is as the strings puppet to the market lathe,
it Cobblers to a Nail and the Venture goes rowe,
than in convenient to the taste of face to eyes,
shoulders squab as pigeon on the soap of dove in detailed.

Creek to that Ditch is at Vanity of popular Crave,
words come to the language to rancid such daze??,
no,
the believed are the all.ways to reality on scene,
therefore the desire is to cover a jam with bumpers and song.

Sheep bay the bah Ram boo to shadow that chalk,
slapping the hand.dull like the fathom did shank,
halters to leadlines cross-tied today,
the chart banks to dumb down to feather just slate.

Caulk to the Grout the be Cans grow lift,
to process know more its the shades be a loud,
dink a round to brink that fade while the light lamp jakes sound,
well is the pitch to the bucket of ground!!!

Stiction

From Wikipedia, the free encyclopedia
Stiction is the static friction that needs to be overcome to enable relative motion of stationary objects in contact.[1] The term is a portmanteau of the term "static friction",[2]perhaps also influenced by the verb "stick".
Any solid objects pressing against each other (but not sliding) will require some threshold of force parallel to the surface of contact in order to overcome static cohesion. Stiction is a threshold, not a continuous force.
In situations where two surfaces with areas below the micrometer range come into close proximity (as in an accelerometer), they may adhere together. At this scale, electrostaticand/or Van der Waals and hydrogen bonding forces become significant. The phenomenon of two such surfaces being adhered together in this manner is also called stiction. Stiction may be related to hydrogen bonding or residual contamination.

Automobiles[edit]

Stiction is a commonly used term when diagnosing diesel fuel powered engines. The Ford Powerstroke 6.0-L and 7.3-L engines are the most prevalent to experience cold start or injector stiction issues. The 7.3-L was produced between 1994 and 2003, while the 6.0-L was produced between 2003 and 2007. Both engines were manufactured by Navistar International and incorporated the HEUI injector system. These injectors use the engine oil to lubricate themselves and over time the sticky friction build up causes the injector to malfunction and fail. Alternatively to replacing injectors with new units, products are available that rid the injector, turbos and transmission of stiction and prevent build up. Leading engineers in the field have found in their research that 9 out of 10 failing injectors in diesel trucks are cases of stiction, and once removed are still in optimal working condition.[3]
Stiction is also the same threshold at which a rolling object would begin to slide over a surface rather than rolling at the expected rate (and in the case of a wheel, in the expected direction). In this case, it's called "rolling friction" or μr.
This is why driver training courses teach that if a car begins to slide sideways, the driver should try to steer in the same direction as the slide with no brakes. It gives the wheels a chance to regain static contact by rolling, which gives the driver some control again. An overenthusiastic driver may "squeal" the driving wheels trying to get a rapid start but this impressive display of noise and smoke is less effective than maintaining static contact with the road. Many stunt-driving techniques are also done by deliberately breaking and/or regaining this rolling friction.
A car on a slippery surface can slide a long way if the driver "locks" the wheels in stationary positions by pressing hard on the brakes. Anti-lock braking systems use wheel speed sensors and vehicle speed sensors to determine if any of the wheels have stopped turning. The ABS Module then briefly releases pressure to that wheel to allow the wheel to begin turning again. Anti-lock brakes can be much more effective than cadence braking which is essentially a non-automatic technique for doing the same thing.

Examples[edit]

Engineering[edit]

Stiction is a problem for the design and materials science of many moving linkages. This is particularly the case for linear sliding joints, rather than rotating pivots. Owing to simple geometry, the moving distance of a sliding joint in two comparable linkages is longer than the circumferential travel of a pivoting bearing, thus the forces involved (for equivalentwork) are lower and stiction forces become proportionally more significant. This issue has often led to linkages being redesigned from sliding to purely pivoted structures, just to avoid problems with stiction. An example is the Chapman strut, a suspension linkage developed by Colin Chapman of Lotus cars.[4]

Surface micromachining[edit]

Stiction or adhesion between the substrate (usually silicon based) and the microstructure occurs during the isotropic wet etching of the sacrificial layer. The capillary forces due to the surface tension of the liquid between the microstructure and substrate during drying of the wet etchant cause the two surfaces to adhere together. Separating the two surfaces is often complicated due to the fragile nature of the microstructure. Stiction is often circumvented by the use of a sublimating fluid (often supercritical CO2, which has extremely low surface tension) drying process where the liquid phase is bypassed. CO2 displaces the rinsing fluid and is heated past the supercritical point. As the chamber pressure is slowly released the CO2 sublimates thereby preventing stiction.

Johansson Gauge Blocks[edit]

These precision machined gauge blocks will stick together with quite high stiction even though they are highly polished and used perfectly dry and clean.

Precision boring[edit]

Many components will lock together with stiction even though they have sufficient theoretical clearance.

Polished glass[edit]

Polished glass is especially prone to stiction.

Hard disk drives[edit]

In the context of hard disk drives, stiction refers to the tendency of read/write heads to stick to the platters. Stiction is a result of smoothness and is exacerbated by humidity and other liquids condensing at the head-disk interface. Once the heads have stuck to the platters, the disk can be prevented from spinning up and can cause physical damage to the media and the slider. Other forces considered as responsible for stiction include electrostatic forces.[citation needed]
In the early models of hard disk drives, stiction was known to cause read/write heads to stick to the platters of the hard drive due to the breakdown of lubricants used to coat the platters. During the late 1980s and early 1990s, as the size of hard drive platters decreased from the older 8" and 5.25" sizes to 3.5" and smaller, manufacturers continued to use the same calendering processes and lubricants used on the older, larger drives. The much tighter space caused much higher internal operating temperatures in these newer smaller drives, often leading to an accelerated breakdown of the surface lubricants into their much stickier components. When the drive was powered off and would cool down (for example at the end of the day when a user went home and shut off their PC), these now-broken-down lubricants would become quite viscous and sticky, sometimes causing the read/write heads to literally stick to the platter. One response to this problem was to remove the affected drive and strike it gently but firmly on the side, then try to start it while connected to but not necessarily fitted inside the machine. This might break the heads free for long enough to spin up the drive and recover the data from it without powering it down. Once started, it would continue to run indefinitely, but might not start again if powered down. Instead of tapping the drive, rotating it sharply by hand could start it. In most Maxtor hard drives, if the heads are stuck to the platters, the drive might make "music" from either the heads trying to move or from the platters trying to spin up.
Modern hard drives have mostly solved the stiction problem by using ramps to "unload" the heads from the disk surface on power-down. These ramps ensure the heads are not touching the platters, which not only prevents stiction but also keeps abrasion from kicking up microscopic particulates that can later contaminate the drive mechanism. Parking the heads in this manner also allows the voice coil actuator to be shut down to save power, so the heads are also frequently unloaded when the drive is idle. A competing solution is based on laser textured landing zones near the ID of the platter where no data are stored. The heads are parked in that zone, and the actuator is latched until the next start-up. The landing zone consists of a controlled array of nanometer-level 'bumps' on the disk surface produced during manufacturing of the disk using a local substrate melting process employing suitable laser-based equipment. The method was pioneered by IBM around 1995 and is still widely in use in most desktop and server class HDDs.[5]

Digital storage tapes[edit]

Stiction may also manifest itself on computer tapes (9 track tape etc.). The magnetic surface of the tape would be heated against the read head in the tape deck, and when the tape stopped moving would cool slightly and "glue" onto the read head. This could be avoided by configuring the software so that the tape could be read continuously.[6]

Amateur astronomy[edit]

The term "stiction" has come into use in amateur astronomy circles to describe a characteristic of Dobsonian style altazimuth telescope mounts. These mounts can resist initial movement by the user, making it difficult to track an object in the sky. There is backlash; breaking this resistance requires enough force to cause the observer to overshoot the object.

Stereolithography[edit]

Typically the phenomenon occurs when “green” epoxy photopolymer components are left in direct contact with each other. If left long enough it appears that “cross-linking” of the polymer takes place in the region of contact. This effectively “welds” or more appropriately “glues” the parts together. This issue can have a significant impact on models where testing of kinematics are required. To avoid stiction in stereolithography clean and more importantly fully cure all geometry prior to assembly.

Biology[edit]

Stiction happens with the human body in situations where two surfaces press together to the point any lubrication is excluded, such as in ball joints for hip replacements or in post-operative transsexuals using smooth plastic dilators.

See also[edit]

    No comments: